Fiberglass Mineral Surfaced Roll Roofing

Fiberglass Roll RoofingFiberglass Mineral Surfaced Roll Roofing is a glass fiber reinforced asphalt coated product with a ceramic granular surface to protect against UV, weathering and physical damage. It is lightly coated with a mineral release material on the bottom side.

Usage

Fiberglass Mineral Surfaced Roll Roofing is a general purpose roofing product designed for use in new roofing and re-roofing installations utilizing hot mopping asphalt, cold process adhesives or mechanical fasteners. While frequently used for residential low-slope applications such as porches and carports or as flashing material, it can also be used as a base sheet in commercial applications.

Features and Benefits

  • Versatile and easy to handle
  • Durable and cost-effective
  • Reinforced with glass fiber mat ensuring dimensional stability during installation
  • Specially formulated asphalt gives lasting performance
  • Minimal dead load weight
  • Multiple options - Full coverage; 4-inch and 19-inch selvage
  • Rolls lay flat and resist wrinkling for easy application
  • Low-slope residential and commercial use
  • Factory controlled characteristics
  • Granular surfacing available in multiple colors to complement most shingle applications
  • Meets ASTM D3909
  • UL Approved in Class A, B, and C roofs (Type G3 BUR)

Available Colors

White, Black, Cedar Blend, Weatherwood, Dark Brown, Red, Hickory, Slate Grey and Green.

Storage and Handling

  • Fiberglass Mineral Surfaced Roll Roofing requires protection from damage and the weather.
  • Constantly store rolls upright in a dry location and never more than two pallets high.
  • When storing two pallets high, position a plywood sheet between pallets.

Application

    • All roofing materials must be kept clean and free of moisture prior to installation.
    • Warm weather conditions are ideal for good adhesion. Application should be made when ambient temperatures are 50° F or higher.
    • Deck must be free of voids, clean and dry.
    • Cut membrane sheets into manageable lengths before installation.
    • Apply over roof decks with inclines of not less than 2 inches per foot.
    • Install in a horizontal manner, overlapping a minimum of 4 inches on side laps and a minimum of 6 inches on end laps.  19-inch Selvage MSR shall be overlapped for the entire 19 inch lap area.
    • To ensure product integrity, do not use in excess of 1/8-inch thickness of lap cement.
    • Excessive use of cement will cause blistering of this product. All cement is to be applied in then, smooth, even layers.

 

  • Install flashings in cement before nailing in place.
  • Nails should be galvanized #11 or 12, a minimum of 1 inch long with 3/8 inch heads and long enough to penetrate the deck.

Tarco shall not be responsible for any damage resulting from failure to follow these instructions.

Properties

Property Typical Value Test Method
Pliability @ 25°C Pass ASTM D228
Unroll @ 50°F and 140°F Pass ASTM D3909
Loss on Heating @ 221°F 0 ASTM D228

Product Data

Property  
Width 36 in.
Length 36 ft.
Gross Coverage 108 sq. ft.
Weight 72 lbs. (nominal)
Rolls Per Pallet 28

Warranty

Fiberglass Mineral Surfaced Roll Roofing is warranted to be free from manufacturer's defects.

Note: All statements information and data given herein are believed to be accurate and reliable, but are presented without guaranty, warranty or responsibility of any kind, expressed or implied, except as may be indicated otherwise in this literature.

Video - FMSRR Application

Quick Reference Product Guide

FMSRR FAQs

Q. What is Mineral Surface Roll Roofing?
A. Mineral Surface Roll Roofing (MSR) is a reinforced sheet that has been coated with asphalt and top-surfaced with rugged colored granules that provide protection of the material from the sun's ultraviolet rays. In residential construction, it is ideal for low-slope roof applications such as roofing for porches, carports, patios and sheds.
Q. Does the product have slope limitations?
A. Yes. Most steep-slope and low-slope roofing materials are designed for use as water shedding systems. These water shedding systems are not impermeable, and they rely on slope to shed water off the roof surface. Adequate drainage of water from the roof surface is essential. A minimum slope of 2 inches per foot is required for the use of MRS.
Q. What colors are available?
A. White, Black, Cedar Blend, Weatherwood, Dark Brown, Red, Hickory, Slate Grey and Green.
Q. What type warranties are available?
A. Tarco warrants material to be free from manufacturing defects.
Q. Can I install MSR in cold process adhesives?
A. Yes. Mineral Surface Roll Roofing can be cold process or hot-asphalt applied.
Q. Does the product have a selvage edge?
A. Yes. MSR is offered in three options - No selvage, 4-inch selvage, and 19-inch selvage .
Q. What is the size and weight of the roll?
A. The product is 108 square foot roll to provide 1 square, or 100 square feet of roof coverage and weighs approximately 72 pounds.

Like us on Facebook

800-365-4506 Toll Free

501-945-4506 Local